Discovering Essential Plumbing Skills is Vital for Bathtub Installation
Discovering Essential Plumbing Skills is Vital for Bathtub Installation
Blog Article
Presented here in the next paragraph you will discover lots of decent news on the subject of How to Install a Bathtub Yourself.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Mounting a bathtub isn't exactly brain surgery, however it does require solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is conveniently easily accessible, the project can relocate quickly; if you have to open a wall to remove the old tub and also position the new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to leave the old bathtub and set in the brand-new one. Make certain you have qualified on your own for the task and fit attempting it. Rather than hiring a professional to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This article will aid you mount a brand-new bathtub in your washroom if you have already gotten a brand-new tub and don't require to change the arrangement of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Planning for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is separate the supply of water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the restricted gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Using both wood boards under its feet, position the bath tub in the required setting. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the tub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and check all joints and new pipework for leaks and tighten them if essential. Fill up the bath tub and likewise inspect the overflow outlet and also the normal electrical outlet for leaks.
Lastly, take care of the bath paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait until the bath tub has been made use of a minimum of when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place between the faucet and the sink. Protect the faucet in position with the maker supplied backnut. As soon as the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, causing the water to pass through the wall in between the bathroom as well as the tiling, leading to issues with wetness and possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the activity experienced when the tub remains in use. The sealant can crack relatively early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our piece on How to Install a Bathtub Yourself. Thank you for taking the time to browse our piece of content. If you appreciated our blog post kindly make sure you remember to pass it around. I praise you for your time. Don't hesitate to pay a visit to our site back soon.
Quality care? Call. Report this page